Chill 211 views Claim this Business♡

For use when installing internal hubs or linear pull brakes on frames lacking necessary housing stops.- Each Backstop accommodates two cables- Cable slots for easy installation- Sold individually- Black only

Accessory lovers often run out of space to mount their widgets. This slim clamp allows for more accessories—computers, lights, mp3 players, cameras, to be mounted for easy to access.Compatibility25.4 - 31.8mm

PROBLEM SOLVERS MIS MATCH ADAPTER 1.2MisMatch adapters allow users to mate Shimano I-Spec components with SRAM MatchMaker X brakes and shifters on one clamp.MISMATCH 1.2 FITS SHIMANO BRAKE LEVERSBL-M9020BL-M9000BL-M8000BL-M7000BL-M6000

Problem Solvers Downtube Shifter Boss Covers.Bolts not included.

PROBLEM SOLVERS MISMATCH 1.0/1.1 ADAPTERSMisMatch adapters allow users to mount Shimano & SRAM brakes and shifters on one clamp. MisMatch Adapter 1.0/1.1 attaches SRAM shifters to Shimano I-Spec-A or I-Spec-B brake lever clamps.MISMATCH 1.0/1.1 FITS THESE SHIMANO BRAKE LEVERS- BL-M985- BL-M988- BL-M...

Our Headtube Reducers adapt your headtube to accommodate different fork sizes. These reducers are designed for traditional, external cup headsets. See Cane Creek's Standardized Headset Identification System (S.H.I.S.) verify compatibility with your frame.

Problem Solvers Downtube Housing Stops- Braze-on downtube adjusters for road shifters- Contoured to fit traditional sized steel downtubes- Satin finish- With bolts

Attach these lightweight brackets to your water bottle bosses to serve as anchors for your cargo straps to carry just about anything, from sleeping pads to Nalgene bottles to barbeque sauce. These are a great addition to any bikepacking or touring cyclist’s on-bike storage toolkit. And their low p...

- For 1-1/8" threadless carbon forks, 28.6mm carbon steerer-fits steerer ID of 22-26mm- Fits steerer tubes with 22–26mm ID- 42g

PROBLEM SOLVERS MISMATCH 1.0/1.1 ADAPTERSMisMatch adapters allow users to mount Shimano & SRAM brakes and shifters on one clamp. MisMatch Adapter 1.0/1.1 attaches SRAM shifters to Shimano I-Spec-A or I-Spec-B brake lever clamps.MISMATCH 1.0/1.1 FITS THESE SHIMANO BRAKE LEVERS- BL-M985- BL-M988- BL-M...

POG top caps are machined aluminum with a 10mm spacer integrated as one piece. This makes for a clean, finished look when mounting a stem below the top of the steerer tube.

Replacement nuts for bolt-on axles with integrated rotating washers. Rotating washers help to keep your wheel securely in your dropouts while you tighten down your wheel. These are a must have item if you have a bolt on wheel! Outside diameter of the washer is 22mm.Part Numbers- PSHU7100 Axle Nuts 1...

The Travel Agent can perform a couple of different tasks; adjusting cable pull or serving as a roller to work around tight frame geometries.For cable pull changes, the Travel Agent makes a short cable pull lever work with along cable pull caliper. This allows you to mix road, mountain and ‘cross b...

Braze-on Adaptor ClampsThese adapters clamp on to the seat tube so you can use your braze-on derailleur on a conventional frame. Available in three common seat tube sizes with 20mm of vertical adjustability.Technical NotesFront derailleur braze-on adaptor clamps for frames without front derailleur b...