Plp 74 views Claim this Business♡

TAARKS threaded water cooling pipe / spigot for the rear side of the engine block.Machined from 304 stainless steel this spigot threads into the intake side of the engine block towards the rear and will not rust out like the factory item.Application:R33 Skyline (RB25DET) "Years: 08/1993 - 02/1997"R3...

TAARKS crank trigger kit for RWD SR20DE(T) and SR20VE(T) motors.Our kit is designed to work in conjunction with the ATI 918582 balancers to provide extremely accurate trigger signals.This kit comes with the choice of a 12 tooth, 24 tooth or 36-2 tooth trigger wheel and utilizes a GENUINE ZF / Cherry...

TAARKS offset power steering pulley.This pulley allows for the 10mm offset created when installing the TAARKS crank trigger kit and re-aligns the belt to correct location.Use the above to select your preferred colour.Suits 3PK belts.Application:S14 Silvia 200sx (SR20) with the TAARKS Crank Tigger Ki...

This plug is used to block off the distributor / Cam Angle Sensor (CAS) hole on the back of the head.Normally used when converting to a coil on plug system.Features:- Double Viton O-Ring Seal- Stainless Steel Bolts & Washers- Anodised Gloss BlackApplication:P11 Primera "SR20VE"P12 Primera "SR20VE"T3...

Stainless Steel Turbo Drain Hose 400mmThese Stainless Steel hoses are designed to withstand the heat which causes most rubber hoses to fail prematurely.- 304 Stainless Steel Gas Pipe- 22mm OD Flexible Pipe- 11.2mm ID- Highly Flexible- Female AN10- Length Measured From Internal Flare To Flare

TAARKS hall sensor kit replaces the CAS and provides the ECU with a trigger and home signals that is less prone to fluctuations / dirty signals.Perfect for a RWD sr20ve conversion as it allows for more clearance between the back of the head and the firewall.Please note: An aftermarket ECU is require...

Changing the knuckles on your S13/180sx to S14/S15 ones? You will notice the S14/S15 uses a large bolt than the S13 knuckle where strut bolts on. Instead of drill your coil overs out and trying to find the right size bolts, just use of adapters. They slide into the S14/S15 knuckles hols and reduce t...

TAARKS pressure sensor mounting block.This block allows you to remote mount up to 3 sensors. This protects the sensors from harsh engine vibrations leading to premature sensor failure.The blocks have 1/8" NPT ports on the bottom, front and top. This allows for great mounting flexibility, you can eve...

TAARKS Updated Knock Sensor Adapter KitThis kit converts the old Nissan single wire knock sensors to the more common Bosch 2 wire knock sensors.Features:- Stainless Steel Mount- Stainless Hardware- Genuine Bosch Knock SensorKit includes:- Stainless Steel Mount- Stainless Steel Bolt & Washers- Genuin...

TAARKS Updated Knock Sensor Adapter KitThis kit converts the old Nissan single wire knock sensors to the more common Bosch 2 wire knock sensors.NOTE: Knock sensor sold separately, if you need a knock sensor we have a kit that includes the knock sensorFeatures:- Stainless Steel Mount- Stainless Hardw...

This kit will bolt onto the front of the SR20 exhaust camshaft and provide the ECU with a home / sync signal Only. Great for use with a crank trigger kit like our kit desined to run with the ATI balancers.We utilise the ZF / Cherry red sensors as they are a proven unit and work extemely well. The tr...

This Dual Channel Hall Sensor has been designed buy TAARKS for use with the TAARKS hall wheel kits. It's also a great sensor for custom applications.The sensor can be independently activated by either a south or north pole of a magnet effectively having 2 sensors in the one housing. Great for trigge...

TAARKS ZF / Cherry Red adapter allows you to use the cherry red sensors in place of the old Honeywell GT101 sensors.Machined from 6061-T aluminum and anodised black.Cherry sensor is not included.

This kit will bolt onto the front of the FWD SR16ve/SR20ve exhaust camshaft and provide the ECU with a home / sync signal only. Great for use with a crank trigger kit like our kit desined to run with the ATI balancers.We utilise the ZF / Cherry black sensors as they are a proven unit and work exteme...

Genuine Nissan timing chain kit.Need to do your 100k service? Then you need to replace that worn out timing chain.This kit comes with either the upgraded S15 (OEM) timing chain tensioner or the TAARKS billet mechanical tensioner. Use the above to make your selection.This kit includes:1x Timing Chain...

Pro Filters are machined from 6061-T6 Aluminium and are a must have for any fuel system. Use in EFI or Carby- 50mm x 140mm Pro Series Filter- Fully Serviceable Stainless Steel Washable 10 Micron Element- 10AN ORB In and Outlet- Internal Magnet- E85 Safe

TAARKS AN6 ORB Fuel Pulse Damper.What is a fuel pulse damper and why do you need one?Fuel pulse dampers are normally attached to the fuel rail and help smooth out pulsations in the fuel pressure caused by the injectors opening and closing. OEM manufactures have been factory fitting these to engine f...

TAARKS AN8 ORB Fuel Pulse Damper.What is a fuel pulse damper and why do you need one?Fuel pulse dampers are normally attached to the fuel rail and help smooth out pulsations in the fuel pressure caused by the injectors opening and closing. OEM manufactures have been factory fitting these to engine f...

TAARKS Inline AN8 ORB Fuel Pulse Damper.What is a fuel pulse damper and why do you need one?Fuel pulse dampers are normally attached to the fuel rail and help smooth out pulsations in the fuel pressure caused by the injectors opening and closing. OEM manufactures have been factory fitting these to e...

TAARKS 1/4" NPT Fuel Pulse Damper.What is a fuel pulse damper and why do you need one?Fuel pulse dampers are normally attached to the fuel rail and help smooth out pulsations in the fuel pressure caused by the injectors opening and closing. OEM manufactures have been factory fitting these to engine...

TAARKS 3/8" NPT Fuel Pulse Damper.What is a fuel pulse damper and why do you need one?Fuel pulse dampers are normally attached to the fuel rail and help smooth out pulsations in the fuel pressure caused by the injectors opening and closing. OEM manufactures have been factory fitting these to engine...

TAARKS Billet SR20 Oil Pan / Sump.Machined from billet 6061-T6 aluminum and anodised to protect against corrosion. Not only do these look great, they add additional oil capacity to the engine and aid in cooling via the fins machined on the underside of the sump. The sump also has hinged gates to hel...

TAARKS top feed fuel rail kit for Toyota 2JZ motors (suits non-VVTi & VVTi).Features:- Designed to clear all factory intake components- 100% bolt on- Center Return Port- AN6 Port for Fuel Pulse Damper (Sold Seperately)- Machined from 6061-T6 Billet Aluminum- Anodised to Protect Against Corrosion- In...